manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 102

1-

80

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-29

Error Code E5-2 

Close Door B

The Left Lower Cover (B) is open.

The Left Lower Cover (B) is closed, but Logic Control on the Print Engine Controller 

Board sensed the Left Lower Cover Interlock Switch is open.

Table 1-57 Error Code E5-2 Close Door B

Step

Actions and Questions

Yes

No

1

LEFT LOWER COVER CHECK

Open and close the Left Lower Cover (B).

Is the error code cleared?

Problem 
solved

Go to step 2

2

LEFT LOWER COVER INTERLOCK SWITCH 
INSPECTION

Inspect the Left Lower Cover Interlock Switch for 
damage.

Is the switch damaged?

Replace the 
Left Lower 
Cover 
Interlock 
Switch

Go to step 3

3

LEFT LOWER COVER INTERLOCK ACTUATOR 
INSPECTION

Inspect the Left Lower Cover (B) Interlock Actuator for 
damage that may prevent the Cover from actuating the 
Interlock when the Cover is closed.

Is the Interlock Actuator damaged?

Replace the 
Left Lower 
Cover

Go to step 4

4

LEFT LOWER COVER INTERLOCK SWITCH 
TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test /  Tray 1 

Cover (B).

3. Actuate and deactuate the Left Lower Cover (B) 

Interlock Switch.

Does the display indicate Open/Closed when 
you actuate and deactuate the Lower Left 
Cover Interlock Switch?

Replace the 
Left Lower 
Cover 
Interlock 
Switch

Go to step 5

5

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 6

Problem 
solved

6

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands