manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 242

1-220

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-30 Multi-sheet Bypass Feeder Feed Roller 
(PL 4.3)

Removal

1.

Remove the Multi-sheet Bypass Feeder Tray Assembly (RRP 1-25).

2.

Remove the Multi-sheet Bypass Feeder Top Cover per Step 3 of RRP 1-26.

3.

Disconnect P/J108 from the Multi-sheet Bypass Feeder No-Paper Sensor 
Assembly.

4.

Loosen the machine screw securing the Multi-sheet Bypass Feeder No-Paper 
Sensor Assembly to the Feeder Assembly and move the Assembly out of the 
way.

5.

Remove the KL-clip securing the Multi-sheet Bypass Feeder Feed Roller to the 
Feed Shaft, and slide the Feed Roller off of the shaft.

Fig 1-60  Multi-sheet Bypass Feeder Feed Roller

Multi-sheet Bypass Feeder
No-Paper Sensor Assembly

Loosen screw

S4525-103

Feed Roller

KL Clip

(P/J108)

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands