manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 112

1-

90

DocuPrint N4525 Network Laser Printer - Service Guide

6

REGISTRATION SENSOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT 

Unit / Reg.  Sensor.

3. Press [4] to start, [0] to stop.
4. Insert, then remove, a sheet of paper into the 

Registration Sensor.

Does the Control Panel display “with paper” 
when you insert the paper into the Registration 
Sensor, and is “without paper” displayed when 
you remove the paper?

Go to step 7

Replace the 
Registration 
Sensor

7

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 8

Problem 
solved

8

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Table 1-63 Error Code C9-3 Paper Jam Reset ENV/Bypass (cont'd.)

Step

Actions and Questions

Yes

No

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands