manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 59

Volume 1 / Print Engine - Error Codes & Messages

1

-

37

Paper Jam
Clear Areas B,C

C8-3

There is a problem with the Tray 3 Take Away 
Sensor.

Logic Control on the Print Engine Controller Board 
sensed the Tray 3 Take Away Sensor was on while 
the printer was in standby.

RAP 
2-10

2-391

Paper Jam
Clear Area C

C8-4

There is a problem with the Tray 4 Take Away 
Sensor.

Logic Control on the Print Engine Controller Board 
sensed the Tray 4 Take Away Sensor was on while 
the printer was in standby.

RAP 
2-11

2-392

Clear Area C
Reset Tray 5

C8-5

Logic Control on the Print Engine Controller Board 
sensed paper remaining at the Take-Away Roller 5 
Sensor. 

RAP 
2-22

2-411

Paper Jam
Clear Duplx Unit

C8-6

There is a paper jam at the Duplex Exit Sensor.

Remaining paper detected in the Duplex Module.

RAP 
3-7

3-520

Paper Jam
Reset 
ENV/Bypass

C9-1

There is a paper jam between the Envelope Tray 
and the Envelope Feed Sensor.

Paper fed from the MBF or the Envelope Feeder did 
not reach the MBF/Envelope Feeder Exit Sensor 
within specified time.

RAP 
4-2

4-566

Paper Jam
Reset 
ENV/Bypass

C9-2

There a paper jam between the Multi-sheet 
Bypass Feeder (MBF) and Tray 2 Take Away 
Sensor.

Logic Control on the Print Engine Controller Board 
sensed that when paper was fed from the Multi-sheet 
Bypeas Feeder, Tray 2 Take Away Sensor did not 
actuate within the specified time after the MBF Feed 
Clutch was acuated.

RAP 
1-34
RAP 
4-3

1-87
4-566

Paper Jam
Reset 
ENV/Bypass

C9-3

There is a paper jam between the Multi-sheet 
Bypass Feeder (MBF) and the Registration 
Sensor.

Logic Control on the Print Engine Controller Board 
sensed that when paper was fed from the Multi-sheet 
Bypass Feeder, the Registration Sensor did not 
actuate within the specified time after the MBF Feed 
Clutch was actuated.

RAP 
1-35
RAP 
4-4

1-89
4-571

Paper Jam
Clear Area A

E1-1

There is a paper jam at the Registration Sensor.

Logic Control on the Print Engine Controller Board 
sensed the paper did not leave the Registration 
Sensor  within the specified time since paper feed.

RAP 
1-18

1-64

Paper Jam
Clear Area A

E1-2

There is a paper jam between the Registration 
Sensor and the Fuser Exit Sensor.

Logic Control on the Print Engine Controller Board 
sensed the Fuser Exit Sensor was not actuated 
within the specified time since the Registration 
Clutch was actuated.

RAP 
1-19

1-66

Paper Jam
Clear Area A

E1-3

There is a paper jam between the Fuser Exit 
Sensor and the Face Up Exit Sensor.

Logic Control on the Print Engine Controller Board 
sensed the Face Up Exit Sensor was not actuated 
within the specified time since the Fuser Exit Sensor 
was actuated.

RAP 
1-20

1-69

Table 1-27 Repair Analysis Procedure (RAP) Table  (cont'd.)

Displayed
Error
Message

Error
Code

Fault Description

Go To 
RAP 
No.

Unit/
Page

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands