Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 362

Page: 362 / 380

1-340

DocuPrint N4525 Network Laser Printer - Service Guide

Table 1-149 Options

Option and Features

Part Number

Custom Paper Tray

Handles continuously variable paper sizes

Holds up to 500 sheets of 80 g/m

(20 lbs.) stock

097S02562

2,500-Sheet Feeder

Three additional trays

Increased paper-printing capacity

Increased printing versatility and convenience

097S02560

Envelope Feeder

Holds 100 standard-weight envelopes

097S02567
097K24870 (Alt.)

Duplex Module

Automatic

duplex capability

097S02561

Face-up Bin

Holds up to 200 sheets

Provides face-up output stacking

097S02564

Finisher with stapler and hole puncher

Increased paper-output capacity

Holds up to 3,000 sheets of 80 g/m

(20 lbs.) stock (Letter,

A4 paper)

Stapling capability

Hole-punching capability

450S02180
3 hole positions

450S02181
4 hole positions

Hard disk drive

5+ Gbyte hard drive

Store resources, fonts, forms, and macros; enables

uninterrupted large-job collation

097S02364

Memory upgrades

Improved system performance

Improved processing of complex jobs

097S02356
(16-Mbyte DIMM)

097S02357
(32-Mbyte DIMM)

097S02358
(64-Mbyte DIMM)

8-Mbyte Flash DIMM

Non-volative memory for downloading and storing fonts,

forms, and macros

097S02360

Ethernet 10Base2 Interface Card

Enables Ethernet 10Base2 connectivity

097S02362

Token Ring interface card

Enables Token Ring connectivity

097S02363

RS232-C serial interface card

Enables Serial connectivity

097S02361

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands

Xerox DocuPrint N4525, Service Quick Reference Manual

Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands