manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 253

Volume 1 / Print Engine - FRU RRPs

1

-

231

Removal

1.

Remove the Rear Cover (RRP 1-5).

2.

Remove the Flywheel Assembly (RRP 1-65)

3.

Disconnect P/J200 from the Registration Clutch.

4.

Remove the E-ring securing the Registration Clutch to the Registration Shaft.

5.

Push out on the shaft latch as you slide the Clutch off of the shaft.

Replacement

1.

Slide the Registration Clutch onto the shaft.  The shaft latch snaps the Clutch 
into place on the shaft.

2.

Use the E-clip (removed in Step 4 above) to secure the Registration Clutch to 
the Registration Shaft.

3.

Reconnect P/J200 from the Registration Clutch.

4.

Reinstall the Flywheel Assembly (RRP 1-65).

5.

Reinstall the Rear Cover (RRP 1-5).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands