manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 3

Users safety summary

Terms in manual:

  Various terms are used throughout this manual to either 

provide additional information on a specific topic or to warn of possible danger 

that might be present during a procedure or action.  Be aware of all symbols and 

terms when they are used, and always read 

NOTE

, 

CAUTION

 and 

WARNING

 

messages.

Terms on product:

Power source:

 

 For 110 VAC printers, Do not apply more than 130 volts RMS 

between the supply conductors or between either supply conductor and ground. 

Use only the specified power cord and connector. For 220 VAC printers, do not 

apply more than 250 volts RMS between the supply conductors or between 

either supply conductor and ground. Use only the specified power cord and 

connector. Refer to a qualified service technician for changes to the cord or 

connector.

WARNING: 

 If the product loses the ground connection, usage of knobs and 

controls (and other conductive parts) can cause an electrical shock. 

NOTE:

A 

NOTE

 may indicate an operating or maintenance 

procedure, practice or condition that is necessary to 

efficiently accomplish a task.

A 

NOTE

 may also provide additional information related to 

a specific subject or add a comment on the results achieved 

through a previous action.

CAUTION:

A 

CAUTION

 indicates an operating or maintenance 

procedure, practice or condition that, if not strictly 

observed, could result in damage to, or destruction of, 

equipment.

WARNING:

A 

WARNING

 indicates an operating, or maintenance 

procedure, practice or condition that, if not strictly 

observed, could result in injury or loss of life.

CAUTION:

A personal injury hazard exists that may not be apparent.  

For example, a panel may cover the hazardous area.

DANGER:

A personal injury hazard exists in the area where you see 

the sign.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands