manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 233

Volume 1 / Print Engine - FRU RRPs

1

-

211

RRP 1-25 Multi-sheet Bypass Feeder Assembly
(PL 4.2)

Removal

1.

Face the left side of the printer.

2.

Hold both sides of the Multi-sheet Bypass Feeder Assembly and firmly pull the 
Assembly toward you and out of the printer.

Replacement

1.

Face the left side of the printer.

2.

Position the Multi-sheet Bypass Feeder against the Multi-sheet Bypass Feeder 
Support.

3.

Tilt the Multi-sheet Bypass Feeder so the Feed Gear slides through the cutout 
in the printer cover.

4.

Hold the Multi-sheet Bypass Feeder Assembly level and push the Assembly 
against the printer, making certain the top cover hides the metal frame.

Fig 1-55  Mult-Sheet Bypass Feeder Assembly

S4525-98

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands