manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 124

1-

102

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-47

Error Code J8-5 

CRUM Failure 

Replace CRU

A Laser Print (EP) Cartridge memory communication error occurred.

Logic Control on the Print Engine Controller Board sensed a wrong or a counterfeit 

Laser Print (EP) Cartridge.

Table 1-75 Error Code J8-5 CRUM Failure Replace CRU

Step

Actions and Questions

Yes

No

1

LASER PRINT (EP) CARTRIDGE 
REPLACEMENT

Replace the Laser Print (EP) Cartridge with a different 
one.

Does the error code still appear?

Go to step 2

Problem 
solved

2

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 3

Problem 
solved

3

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands