manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 113

Volume 1 / Print Engine - Error Codes & Messages

1

-

91

RAP 1-36

Error Code H1-1 

Insert Tray 1

There is a Lift Up problem with Tray 1.

Logic Control on the Print Engine Controller Board sensed that Tray 1 was not raising 

into position in Feeder 1.

Table 1-64 Error Code H1-1 Insert Tray 1

Step

Actions and Questions

Yes

No

1

Tray 1 LIFT MOTOR TEST

1. Remove the Rear Cover (RRP 1-5).
2. Load paper into Tray 1 and install Tray 1 into Feeder 1.
3. Enter Diagnostics Mode.
4. From the Main Menu, select Comp Output Test / IOT 

Unit / Tray 1 Lift Mot to check the Tray 1 Lift Motor.

5. Press [4] to start, Tray 1 Lift Motor should run two 

seconds, then stop.

Does the Tray 1 Lift Motor run when you start 
the test?

Go to step 2

Replace Tray 
1 Lift Motor 
(RRP 1-9)

2

Tray 1 CHECK

Slowly side Tray 1 out of Feeder 1.

Can you hear the Tray 1 bottom plate drop as 
you slide the Tray out of the Feeder?

Go to step 2

Replace Tray 
1 with a new 
one

3

Tray 1 LEVEL SENSOR TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Input Test / IOT 

Unit / Tray 1 Level to check the Tray 1 Level Sensor.

3. Press [4] to start, [0] to stop.
4. Repeatedly open and close Tray 1.

Does the Control Panel display “Up” when you 
open the Bin, and “Down” when you close the 
Bin?

Go to step 4

Replace the 
Tray 1 Level 
Sensor

4

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 5

Problem 
solved

5

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands