manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 173

Volume 1 / Print Engine - Diagnostics, Tests & NVRAM

1

-

151

Maintenance Reset Procedure

The Maintenance Kit is a user installable kit which replaces the paper feed rollers, bias 
transfer roller, cleaning cloth, gloves and a fuser.  The printer’s control panel display 

informs the user when it is time to install a Maintenance Kit.

Upon completing the Maintenance Kit installation, it is necessary to reset the Maintenance 

Kit Counter.  Although wordless instructions are included with the kit, the procedure 
below is provided for when those instructions are not available to you.

Note

The Maintenance Kit Counter should only be reset when a 

complete kit has been installed.

Maintenance Kit Counter Reset Procedure

1.

Make certain the printer is OFF.

2.

Press and hold buttons [2] and [6] on the Control Panel while you switch ON 
printer main power.  Continue holding until 

*

IOT?

*

 

appears in the display 

(approximately 20 seconds).

3.

When the Control Display shows 

*

IOT?

*

, 

release buttons [2] and [6], then 

press and hold button [0] and [5].  You have 10 seconds to release [2] and [6] 
and press [0] and [5].  Hold [0] and [5] until “Reset Complete Please Reboot” is 
displayed.  This message confirms the counter has been reset.

4.

Reboot the printer by powering OFF, waiting 20 - 30 seconds and powering 
ON.

The Maintenance Kit is a customer purchased / customer replaced unit (CRU).  The 
interval for replacement is 300K prints.

For Maintenance Kit part numbers, see Xerox Supplies and Accessories in the FRU Parts 

Lists on page 1-338.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands