manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 184

1-162

DocuPrint N4525 Network Laser Printer - Service Guide

Tray Size Test

The tray size test provides a convenient method of checking the paper feed tray sizes from 

the Control Panel.  This is a tray size test only.  No adjustments can be made.

Information displayed here requires entering Diagnostics Mode.  Refer to page 1-154 for 
instructions on entering Diagnostics Mode.

The Control Panel Test Legend to the right will aid in 
navigating through the variety of tests available.  Press [4] to 

start the test selected, press [0] to stop.

Table 1-105 Tray Size Test

Press [1] or [5]

Press [2] or [6]

Press (3) or (7) to display “value”.
Continue pressing [3] or [7] to adjust 
“value”.

to display: 

ß

to display: 

ß

Press [4] to write to NVRAM, [0] to exit.

Main Menu
Tray Size Test

Tray Size Test
Tray 1 Size

Press [4] start, [0] stop

Tray 1 paper size is displayed 

Tray Size Test
Tray 2 Size

Press [4] start, [0] stop

Tray 2 paper size is displayed

Tray Size Test
Tray 3 Size

Press [4] start, [0] stop

Tray 3 paper size is displayed

Tray Size Test
Tray 4 Size

Press [4] start, [0] stop

Tray 4 paper size is displayed

Tray Size Test
Tray 5 Size

Press [4] start, [0] stop

Tray 5 paper size is displayed

Tray Size Test
MBF Tray Size

Press [4] start, [0] stop

MBF Tray paper size is displayed 

Tray Size Test
Env Tray Size

Press [4] start, [0] stop

ENV Tray envelope size is displayed

Stop

Start

Menu Up

Item Up

Value Up

Menu
Down

 Item
Down

Value
Down

S4525-25B

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands