manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 115

Volume 1 / Print Engine - Error Codes & Messages

1

-

93

RAP 1-38

Error Code H2-7 

Duplex Unit Fail 

Power Off/On

There is a communication problem between the printer and the Duplex Unit.

Logic Control on the Print Engine Controller Board could not initialize the Duplex 

Unit within the specified time.

Table 1-66 Error Code H2-7 Duplex Unit Fail Power Off/On

Step

Actions and Questions

Yes

No

1

LOW VOLTAGE POWER 5VDC 
CHECK

Measure the voltage between J400, pins 1, 2 & 3 (on the 
Print Engine Controller Board) and frame ground.

Is there +5VDC between J400, pins 1,2 & 3 and 
frame ground?

Go to step 2

Replace the 
Low Voltage 
Power Supply 
Assembly 
(RRP 1-67)

2

DUPLEX BOARD REPLACEMENT

Replace the Duplex Module Board (RRP 3-5).

Does the error code appear?

Go to step 3

Problem 
solved

3

PRINT ENGINE CONTROLLER BOARD 
REPLACEMENT

Replace the Print Engine Controller Board (RRP 1-72).

Does the error code appear?

Go to step 4

Problem 
solved

4

The following printer components and areas are 
associated with this specific problem.  One or more of 
these components or areas may have failed partially or 
completely.  If you cannot isolate this problem using the 
steps in this Repair Analysis Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Wiring and connectors linking the components

Input/Output Board (RRP 1-70).

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands