manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 256

1-234

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-43 Left Chute Assembly (PL 6.2)

Removal

1.

Open the Left Upper Cover.

2.

Remove the Bias Transfer Roller Assembly.

3.

Push down on the rear of the Chute Assembly and use the blade of a small 
screwdriver to free the rear latches from the Cover.

4.

Push down on the front of the Chute Assembly and use the blade of a small 
screwdriver to free the front latches from the Cover.

5.

Remove the Left Chute Assembly.

6.

Release the two springs and remove the Registration Roller Assembly from the 
Chute Assembly.

Fig 1-69  Left Chute Assembly

Registration Roller

S4525-115

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands