manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 196

1-174

DocuPrint N4525 Network Laser Printer - Service Guide

Press [2]  or [6] to 
display: 

ß

Press [3]  or [7] to 
display: 

ß

Turn -On
Duration

Comment

TTM Feed Motor

2 min.

1. Press [4] to start test.
2. Actuate TTM Feed Motor for duration or 

Press [0] to stop.

Tray 3 Feed Clut

2 sec.

1. Press [4] to start test.
2. Actuate Tray 3 Feed Clutch for duration or 

Press [0] to stop.

Tray 4 Feed Clut

2 sec.

1. Press [4] to start test.
2. Actuate Tray 4 Feed Clutch for duration or 

Press [0] to stop.

Tray 5 Feed Clut

2 sec.

1. Press [4] to start test.
2. Actuate Tray 5 Feed Clutch for duration or 

Press [0] to stop.

Comp Output Test
Duplex Unit

Motor Slow

2 min.

1. Press [4] to start test.
2. Actuate Exit Motor slow for duration or 

Press [0] to stop.

Motor Fast

2 min.

1. Press [4] to start test.
2. Actuate Exit Motor fast for duration or  

Press [0] to stop.

Exit Gate Sol.

2 sec.

1. Press [4] to start test.
2. Actuate the Exit Gate for duration or  Press 

[0] to stop.

Wait Clutch

2 sec.

1. Press [4] to start test.
2. Actuate Wait Clutch for duration or  Press 

[0] to stop.

Invert Clut CW

2 sec.

1. Press [4] to start test.
2. ActuateClockwise Invert Clutch for duration 

or Press [0] to stop.

Invert Clut CCW

2 sec.

1. Press [4] to start test.
2. Actuate Counter Clockwise INvert Clutch 

for duration or Press [0] to stop.

Comp Output Test
MBF/ENV Unit

MBF Feed Clutch

2 sec.

1. Press [4] to start test.
2. Actuate Multi-sheet Bypass Feeder feed 

clutch for duration or Press [0] to stop.

Env Feed Motor

2 min.

1. Press [4] to start test.
2. Actuate Envelope Feed Motor for duration 

or  Press [0] to stop.

Env Clutch On

2 sec.

1. Press [4] to start test.
2. Actuate Envelope Feeder feed clutch for 

duration or Press [0] to stop.

Comp Output Test
Finisher Unit

Finisher Unit
Fin Main Motor

2 min.

1. Press [4] to start test.
2. Actuates Finisher Main Motor for duration 

or  Press [0] to stop.

Finisher Unit
Compile Tray Mot

2 min.

1. Press [4] to start test.
2. Actuate Compile Tray Motor for duration or  

Press [0] to stop.

Finisher Unit
Exit Motor CW

2 min.

1. Press [4] to start test.
1. Actuates Exit Motor clockwise for duration 

or Press [0] to stop. 

Finisher Unit
Exit Motor CCW

2 min.

1. Press [4] to start test.
2. Actuates Exit Motor counter clockwise for 

duration or Press [0] to stop. 

Finisher Unit
Exit Motor Open

2 sec.

1. Press [4] to start test.
2. Actuates Exit Motor Open function.

Finisher Unit
Exit Motor Close

2 sec.

1. Press [4] to start test.
2. Actuates Exit Motor Close function.

Table 1-107 Component Control Output

Press [1] or [5] to display: Main Menu

Comp Output Test

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands