manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 279

Volume 1 / Print Engine - FRU RRPs

1

-

257

Removal

1.

Remove the Fuser cover (RRP 1-1).

2.

Remove the Top Cover Assembly (RRP 1-2).

3.

Remove the Front Inner Cover (RRP 1-4)

4.

Remove the Right Cover (RRP 1-6).

5.

Remove the four machine screws securing the System Controller Assembly to 
the Low Voltage Power Supply, and tilt the System Controller Assembly back 
and out of the way (Figure 1).

6.

Remove the machine screws securing the Low Voltage Power Supply Cover to 
the Low Voltage Power Supply and remove the Cover (Figure 2).

7.

Disconnect J1, J3, J220, J502, J504, J505, and J506 from the Low Voltage 
Power Supply (Figure 3).

8.

Remove the wire harnesses from the harness clips at the rear of the Low 
Voltage Power Supply.

9.

Remove the five machine screws securing the Low Voltage Power Supply to 
the printer frame (Figure 3).

10.

Remove the Low Voltage Power Supply Assembly.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands