manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 142

1-120

DocuPrint N4525 Network Laser Printer - Service Guide

4

IMAGE TRANSFER INSPECTION

1. Remove the Rear Cover (RRP 1-5).
2. Generate a Solid Black Test Print and switch OFF 

printer power halfway through the print cycle.

3. Open the Left Upper Door.
4. Open the Drum Shutter.
5. Hand rotate (counter clockwise) the Drum Drive Motor 

flywheel to advance the Drum far enough so you can 
see the developed image area on the Drum before it 
reached Transfer.

Before Transfer was the toner image on the 
drum normal and without vertical band 
deletions, but there were deletions after 
transfer?

Replace the 
Bias Transfer 
Roller 
Assembly

Go to step 5

5

FUSER INSPECTION

1. Generate another Solid Black Test Print and switch 

OFF printer power when the print is halfway through 
the Fuser.

2. Open the Left Upper Door.
3. Examine the paper areas before the image enters the 

Fuser and after the image exits the Fuser.

Is the image on the paper normal before it 
enters the Fuser, but there are vertical band 
deletions visible when it exits the Fuser?

Replace the 
Fuser 
Assembly

Go to step 6

6

The following printer components and areas are 
associated with this specific problem. One or more of 
these components or areas may have failed partially or 
completely. If you cannot isolate this problem using the 
steps in this Fault Isolation Procedure, replace each 
component or troubleshoot each area listed below, one at 
a time, until you isolate and solve the problem.

Refer to the wiring diagrams, See “Master 

Connection and Wiring Diagram” on page 356. 
and check for a broken wire or loose connection 
between components in the Xerographic sections 
of the printer.

Table 1-87 Vertical Band Deletions (cont'd.)

Step

Actions and Questions

Yes

No

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands