manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 174

1-152

DocuPrint N4525 Network Laser Printer - Service Guide

Test Prints

A variety of test prints are available to aid in determining the quality of output from the 
printer and to assist in troubleshooting problems.  Some test prints are available from the 

System Controller Board and others from the Print Engine Controller Board  This section 
shows how to select and produce all test prints available.

Note

For assistance in analyzing print quality problems, please refer to 
the Troubleshooting section of this manual, Image Quality 

Problems on page 1-113.

System Controller Test Prints

The test prints available from the System Controller Board consist of a “Test Print” for 

helping to evaluate print quality and alignment/registration.  Other available prints provide 
a printer configuration sheet, fault history, menu map, PS and PCL font lists, and a PCL 

Demo page.  Some of these test prints serve a twofold purpose by providing information 
germaine to the printer and an indicator of measurable print quality.

Note

If multiple test prints are desired, enter the System Menu and 

change “Print Quantity” value from 1 to the desired number. 
Remember to reset the value back to 1 after checking/adjusting 

registration.

Note

It is not necessary to take the printer “Off Line” to run the 
following test prints.  The [0] key takes the printer Off Line, if 

needed and returns all modes, except Diagnostics, to “Ready.”

Configuration Sheet:

A printer configuration sheet can be used as an indicator of print quality, as well as 

providing the user/technician with myriad of pertinent information regarding the printer’s 
configuration.  It is a good idea to print a configuration sheet and keep it close to the 

printer for reference by users, technicians, and/or system administrators.

1.

While in the menu mode, press [1] or [5] until “Print Menu” is  displayed.

2.

Press [2] or [6] until “Config Sheet” is displayed.

3.

Press [4] and a printer configuration sheet will be printed.

System Controller Test Print:

The “Test Print” is a multi-purpose print displaying a wide 

variety of objects including text, multi-positional thin/thick 
lines, black painted areas, gray scale, fine alignment 

graduations to facilitate checking registration, lead edge and 
side edge alignment, etc.  Normally, running this test print 

delivers two identical pages.

1.

While in the menu mode, press [1] or [5] until “PRINT 
MENU” is displayed.

2.

Press [2] or [6]  until “Test Print” is displayed.

3.

Press [4] and the System Controller test page will be 
printed.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands