Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 167

Page: 167 / 380

Volume 1 / Print Engine - Troubleshooting

145

RAP 1-77

Side-to-Side Registration Is Not Correct

PROBLEM

The printed image is not centered on the page. The side
margins are not equal and the image may be cut off on either
the left or right side.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-32 Side-to-Side Registration Is Not Correct

Table 1-101 Side-to-Side Registration Is Not Correct

Step

Actions and Questions

Yes

PAPER Tray INSPECTION

Inspect the paper that is loaded in the paper Bin.

Is the paper loaded correctly and are the paper
guides adjusted correctly?

Go to step 2

Reload the
paper and
adjust the
paper guides

SIDE-TO-SIDE REGISTRATION

Refer to the Diagnostics, Test Prints, Service Tests &
NVRAM Adjustments section of this manual and use
NVRAM to adjust Side Edge Registration.

Can you adjust side-to-side registration using
NVRAM?

Problem
solved

Go to step 3

1. Reload print driver software.
2. Generate 5 Test Prints.

Is the side-to-side registration correct?

Problem
solved

Go to step 4

1. Replace the Print Engine Controller Board (RRP

1-72).

2. Generate 5 Test Prints.

Is the side-to-side registration correct?

Problem
solved

Go to step 5

1. Replace the Laser Scanner (RRP 1-47)
2. Generate 5 Test Prints.

Is the side-to-side registration correct?

Problem
solved

Go to step 6

S4525-23

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands

Xerox DocuPrint N4525, Service Quick Reference Manual

Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands