manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 284

1-262

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-72 Print Engine Controller Board
 (PL 11.3)

Removal

Caution

Wear an electrostatic wrist strap and use caution when working 
with the 

Print Engine Controller Board

. Static electricity can 

damage the sensitive electronics of the 

Print Engine Controller 

Board

.

1.

Remove Fuser Cover (RRP 1-1).

2.

Remove Top Cover (RRP 1-2).

3.

Remove the System Controller Board (RRP 1-73). 

4.

Remove the System Controller Assembly Cover by removing the 14 machine 
screws securing the cover to the assembly, then lifting the cover off of the 
assembly.

5.

Disconnect the six P/Js (J400, J402, J403, J404, J408 and J411) and the video 
plug (P409) that are connected to the Print Engine Controller Board.

6.

Remove the six screws securing the Print Engine Controller Board to the 
System Controller Assembly.

7.

Remove the two 7mm nuts from J406.

8.

Lift the Print Engine Controller Board out of the System Controller Assembly.

9.

Remove the U9 EEPROM from the Print Engine Controller Board and retain.

Replacement

1.

Install the U9 EEPROM from the “old” Print Engine Controller Board onto the 
“new” board.

Fig 1-94  Print Engine Controller Board

U9

S4525-143

(J406)

Remove Screws

Remove Pin Guides

(P409)

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands