manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 37

Volume 1 / Print Engine - General Information

1

-

15

Physical Dimensions

Note

Above measurements taken with the Multi-sheet Bypass Feeder 

(MBF) retracted.

Note

Above minimum space requirements are measured from the 

printer covers to the wall or neighboring  object.

Table 1-2 Physical Dimensions

Dimensions

Specification

Height

486 mm / 19.1 /- 1%

Width

645 mm / 25.4 /- 1%

Depth

540 mm / 21.3 /- 1%

Weight (110 V model)

48.5 Kg / 106.92 Lbs. +/- 1%  (65.0 Kg / 143.3 Lbs. packaged for 
shipment)

Weight (220 V model)

53.0 Kg / 116.85 Lbs. +/- 1% (69.5 Kg / 153.22 Lbs. packaged for 
shipment)

Table 1-3 Printer Clearances

Clearances

Specification

Front

460 mm / 18.1 inches

Back

200 mm / 7.9 inches for ventilation

Right

200 mm / 7.9 inches without Finisher
1000 mm / 39.4 inches with Finisher

Left

364 mm / 14.3 inches without Duplex Unit installed.
640 mm /  25.2 inches with Duplex Unit installed.

Top

Typically 762 mm / 30 inches

Bottom

No obstruction under printer that could block cooling vents

Mounting surface flatness

Within 2 degrees of horizontal with all four feet in contact with the 
table surface

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands