manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 261

Volume 1 / Print Engine - FRU RRPs

1

-

239

RRP 1-51 Laser Print Cartridge Interlock Switch (PL 
7.2)

Removal

1.

Remove the Laser Print (EP) Cartridge.

2.

Remove the Rear Cover (RRP 1-5).

3.

Disconnect J232 and J233 from the Laser Print Cartridge Interlock Switch.

4.

Disconnect P/J234 from the Interlock Switch wire harness.

5.

Remove the screw securing the Laser Print Cartridge Interlock Switch to the 
printer frame, and remove the Switch.

Fig 1-74  Laser Print Cartridge Interlock Switch

S4525-122

(P/J233)

(P/J232)

(P/J234)

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands