manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 280

1-258

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-68 AC Driver Board (PL 11.2)

Removal

1.

Remove the Input/Output Board (RRP 1-70).

2.

Remove the five P/Js (J30, J31, J32, J33 and, J510) from the AC Driver Board.

3.

Remove the two machine screws securing the Plate, Bracket, and AC Drive 
Board to the frame and remove the Bracket and the Plate.

4.

Press in on the two latches securing the top of the AC Driver Board to the 
printer frame and remove the board.

Fig 1-90  AC Driver Board

AC Driver PWB 230V FLK

Bracket

Plate

AC Driver PWB 20A 120V

Figure 1

Figure 2

S4525-139

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands