manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 56

1-

34

DocuPrint N4525 Network Laser Printer - Service Guide

Before Starting the Error Code Repair 
Analysis Procedures:

1.

Is the AC power provided at the wall outlet within specifications for this printer; 
either 110VAC or 220VAC?

2.

Is the AC power cord in good condition (e.g.  frayed or broken)?

3.

Is one end of the AC power cord connected to the printer?

4.

Is the other end of the AC power cord plugged into a grounded three-prong AC 
wall outlet?

5.

Is the printer located in an area where the temperature and humidity are 
moderate and stable as recommended in the General Information section.

6.

Is the printer located in an area that is free of dust?

7.

Is the printer located away from water outlets, steamers, electric heaters, 
volatile gases, or open flames?

8.

Is the printer shielded from the direct rays of the sun?

9.

Does the printer have the correct ventilation space around all sides as 
recommended in the General Information section.

10.

Is the printer sitting on a level and stable surface?

11.

Is the paper stock used in the printer as recommended in the User Manual?

12.

Does the customer use the printer as instructed in the User Manual?

13.

Are consumables replaced at the intervals recommended in the General 

Information section.

14.

Are all of the printer assemblies in place and are all printer covers and doors 

firmly closed?

Note

Repair Analysis Procedures assume there is no malfunction in the 

System Controller Board.  If you are unable to fix a problem using 
the Repair Analysis Procedures, it is recommended that you refer 

to the System Controller Error Codes on page 1-44.  If all else 
fails,  replace the System Controller board.

Repair Analysis Procedures (RAP)

Depending on the level of firmware on your Print Engine Controller Board some codes 
listed in this table may be invalid, some codes generated may not appear in this table, and 

Error and Message Code text presented in this table may differ slightly from the Error and 
Message Code text appearing on the Control Panel display.  In some cases, where no RAP 

is indicated, follow the displayed message to clear the problem

Table 1-26 Legend

Term

Definition

Comment

PE

Print Engine

Sometimes referred to as “IOT” (Image Output 
Terminal) and appears in the display on the Control 
Panel as a result of programming.

HCF

High Capacity Feeder

Option

DUP

Duplex Module

Option

ENV

Envelope Feeder

Option

FIN

Finisher

Option

SE

Sensor

Abbreviated sensor callout identifier

SW

Switch

Abbreviated switch callout identifier

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands