manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 219

Volume 1 / Print Engine - FRU RRPs

1

-

197

Removal

1.

Remove the paper Tray from the appropriate feeder.

2.

Swing the Chute down so it clears the Rollers.

3.

Pull out on the Roller latch and slide the Roller off of the shaft.

4.

Repeat step 3 for the remaining two Rollers.

Replacement

1.

Swing the Chute down so it clears the Rollers.

2.

Position the Roller with the latch end facing out, and slide the Roller onto the 
shaft.

3.

Rotate and push the Roller down the shaft until the latch locks the Roller into 
place.

4.

Repeat steps 2 and 3 for the remaining two Rollers.

5.

Reinstall the paper Bin.

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands