manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 188

1-166

DocuPrint N4525 Network Laser Printer - Service Guide

Service Tests

The printer utilizes an extensive variety of Component Control Input and Output tests to 
aid in diagnosing funtional problems.  The following Diagnostic Service Tests are 

provided by the System Controller Board.

Component Control Input

Component Control Input tests are used to aid in verifying proper component operation 
and identifying problems and isolating faulty components.  To access the following tests, 

you must enter Diagnostics Mode:

1.

Enter Diagnostics Mode - press and hold [2] and [6] while powering up the printer.  
Continue holding [2] and [6] until *IOT?* is displayed.

2.

Release [2] and [6], then press and hold [4] until “Main Menu” appears in the top line 
of the display.  You are now in Diagnostics Mode.

3.

Use the Legend below to help navigate throught the various items in the Component 
Control Input Tests table.

4.

Press [1] or [5] until “Main Menu Comp Input Test” is displayed.

5.

Follow the table headings, and the Control Panel Test Legend below, to navigate to the 

desired test.

The tests in the table below enable the technician to test the many input sensors and 
switches providing vital information to the Print Engine Controller Board.  

Control Panel Test Legend:

Nomenclature Legend:
IOT

: Print Engine - the printer not including the 

System Controller Board or options.

HCF 

: High Capacity Feeder Option

MBF (or MSI)

: Multi-sheet Bypass Feeder

ENV

: Envelope Feeder Option

Fin

: Finisher Option

ROS

: Laser Scanner

Table 1-106 Component Control Input Tests

Press [1] or [5] until to display: 

 

Main Menu
Comp Input Test

Press [2]  or [6] to 
display: 

ß

Press [3]  or [7] to 
display: 

ß

Action To Take

Displayed Result

Comp Input Test
IOT Unit

IOT Unit
L/H Cover A

1. Press [4] to begin test.
2. Open L/H Cover A.
3. Press [0] to end test.

Close
Open

IOT Unit
Tray 1 Cover B

1. Press [4] to begin test.
2. Open Tray 1 Cover B.
3. Press [0] to end test.

Close
Open

IOT Unit
Front Cover

1. Press [4] to begin test.
2. Open Front Cover.
3. Press [0] to end test.

Close
Open

Stop

Start

Menu Up

Item Up

Value Up

Menu
Down

 Item
Down

Value
Down

S4525-25B

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands