manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 286

1-264

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-73 System Controller (PL 11.3)

Removal

1.

Turn OFF the printer.

Caution

Wear an electrostatic wrist strap and use caution when working 

with the System Controller Board. Static electricity can damage 
the sensitive electronics of the System Controller.

2.

Disconnect all input cables from the connectors on the System Controller 
Board Panel.

3.

Loosen the two thumbscrews that secure the System Controller Assembly 
Panel to the System Controller Box.

4.

Slide the System Controller Board out of the System Controller Box.

5.

Place the System Controller Board and the attached Drawer Panel on a 
grounded anti-static work mat.

Fig 1-95  System Controller

System Controller Board

Panel

S4525-144

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands