manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 164

1-142

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-75

Repetitive Marks on Each Page

.

PROBLEM

Identical image defects appear on each or on every other 
printed sheet.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-30  Repetitive Marks on Each Page

Table 1-99 Repetitive Marks on Each Page

Step

Actions and Questions

Yes

No

1

DRUM IMAGE INSPECTION

1. Generate a single Test Print.
2. Open the Upper Left Cover when the sheet of paper is 

approximately half-way through the transfer process.

3. Carefully remove the Laser Print (EP) Cartridge from 

the printer.

4. Inspect the surface of the Drum.

Does the mark appear on the Drum before 
image transfer?

Replace the 
Laser Print 
(EP) 
Cartridge

Go to step 2

2

TRANSFER IMAGE INSPECTION

Inspect the Test Print generated in step 1.

Does the mark appear on the paper after image 
transfer?

Replace the 
Bias Transfer 
Roller 
Assembly

Go to step 3

3

FUSED IMAGE INSPECTION

1. Generate a single Test Print.
2. Open the Upper Left Cover when the sheet of paper is 

approximately half-way through the Fuser.

3. Inspect the Test Print.

Does the mark appear on the paper after 
Fusing?

Replace the 
Fuser 
Assembly

S4525-21

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands