manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 70

1-

48

DocuPrint N4525 Network Laser Printer - Service Guide

RAP 1-2

Error Code U1-3 

LVPS Fan 

Failure

There is a problem with the Low Voltage Power Supply Fan.

Logic Control on the Print Engine Controller Board detected a problem with the Low 

Voltage Power Supply Fan.

Table 1-30 Error Code U1-3 LVPSFan Failure

Step

Actions and Questions

Yes

No

1

LOW VOLTAGE POWER SUPPLY FAN TEST

1. Enter Diagnostics Mode.
2. From the Main Menu, select Comp Output Test / LVPS 

Fan High to check the Low Voltage Power Supply Fan 
function.

3. Press [4] to start, [0] to stop.

Does Fan rotate when you start theLVPS Fan 
Output Test?

Replace the 
Print Engine 
Controller 
Board (RRP 
1-72)

Replace the 
Low Voltage 
Power Supply 
cooling fan 
(RRP 1-67)

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands