Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 147

Page: 147 / 380

Volume 1 / Print Engine - Troubleshooting

125

RAP 1-66

Horizontal Streaks

PROBLEM

There are black lines running horizontally across the paper
perpendicular to the direction of paper movement.

THE PRINTER DISPLAYS NO ERROR CODE.

Fig 1-21 Horizontal Streask

Table 1-90 Horizontal Streaks

Step

Actions and Questions

Yes

LASER PRINT (EP) CARTRIDGE
REPLACEMENT

Install a new Laser Print (EP) Cartridge.

Are the horizontal streaks gone?

Problem
solved

Go to step 2

IMAGE DEVELOPMENT INSPECTION

1. Remove the Rear Cover (RRP 1-5).
2. Generate a Blank Test Print and switch OFF printer

power halfway through the print cycle.

3. Open the Left Upper Cover.
4. Open the Drum Shutter.
5. Hand rotate (counter clockwise) the Drum Drive Motor

flywheel to advance the Drum far enough so you can
see the developed image area on the Drum before it
reached Transfer.

Is the image on the drum completely white;
without any horizontal streaks visible?

Go to step 3

Replace the
Laser
Scanner
Assembly
(RRP 1-47)

IMAGE TRANSFER INSPECTION

Inspect the Blank Test Print you generated in step 2.

Are horizontal streaks visible on the paper
after Transfer?

Replace the
Bias Transfer
Roller
Assembly

Go to step 4

S4525-12

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands

Xerox DocuPrint N4525, Service Quick Reference Manual

Search results

Summary of Contents for DocuPrint N4525

Reviews:

Brands by name

Popular brands