manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 226

1-204

DocuPrint N4525 Network Laser Printer - Service Guide

RRP 1-20 Tray 1 & Tray 2 Paper Size Sensors
 (PL 3.1~PL 3.4)

Note

Use this procedure to remove and replace the Paper Size Sensors 

for Bins 1 and 2.

Removal

1.

Remove either Paper Tray 1 or Paper Tray 2 from the printer.

Caution

Do not lay paper Bins flat on carpeted floors.  The carpet can 
grab the spring on the bottom of the Tray and, when lifted, the 

spring may pop off, rendering the paper Tray useless.

2.

Disconnect the P/J from the Size Sensor Board.

3.

Remove the screw securing the Size Sensor Board to the printer frame, pull the 
board straight out and remove it from the frame.

Fig 1-50  Tray 1 & Tray 2 Paper Size Sensors

Paper Size Sensor Board

S4525-93

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands