manualshive.com logo in svg

Xerox DocuPrint N4525, Service Quick Reference Manual

Share
Download
Xerox DocuPrint N4525 Service Quick Reference Manual Download Page 259

Volume 1 / Print Engine - FRU RRPs

1

-

237

RRP 1-47 Laser Scanner Assembly (PL 7.1)

Removal

1.

Remove the Low Voltage Power Supply (RRP 1-67).

2.

Disconnect the J106, J207, J407, and J430 from the Laser Scanner.

3.

Remove the three screws that secure the Laser Scanner to the printer frame.

4.

Lift the Laser Scanner Assembly off of the printer frame.

5.

Place the Laser Scanner Assembly on a flat and stable surface.

Warning

Do not remove Laser Scanner covers or disassemble the Laser 

Scanner Assembly. There are no replaceable parts or field 

adjustable points located inside the Laser Scanner Assembly.

Fig 1-72  Laser Scanner Assembly

S4525-118

Summary of Contents for DocuPrint N4525





























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands