363-206-285
Detailed Level Procedure:
DLP-562
Issue 2, February 2000
Page 3 of 12
DDM-2000 OC-3 M
ULTIPLEXER
NOTE:
When the
ins-prog:
or
cpy-prog:
command is used for software
upgrades from Release 9.1 or later, the software is loaded as a dormant
copy in the SYSCTL receiving the software. At the end of the download,
the
rtrv-alm:
report will show a status message of
dormant/exec code mismatch
. The
apply:
command must be
used to overwrite the original executing copy of software with the new
dormant software version. See the Commands and Reports section in
Volume 1 of this manual for a description of the TARP Release 13.0 and
15
apply:
command.
Before performing this procedure, ensure that both TGS/TG3 circuit packs are
installed in the shelf receiving the program, then use the
switch-sync:s=circuitpack,pri=manual
command to switch to the
protection TGS/TG3 circuit pack in TIMING slot 2, if not already ACTIVE. Use
rtrv-sync:
command to verify that the protection TGS/TG3 circuit pack in
TIMING slot 2 is ACTIVE.
5.
NOTE:
If you want to load new software to a remote shelf (if allowed) directly
from a PC, use the
ins-prog:tid
or
ins-prog:tid,pgmtype=nesw
command where the tid entered is
that of the remote shelf where you want to install the new software and
the pgmtype is the type of software you want to install. After using the
ins-prog:tid
or
ins-prog:tid,pgmtype=nesw
command to
download software to one shelf, you must exit
term
(Alt F2) and
re-execute
term
before starting a second
ins-prog:
command. If
term
is not exited, it will stop running if a second
ins-prog:
is started
within the same
term
session. The PC will not respond or return any
message and the
ins-prog:
will not progress.
NOTE:
If remote software downloading is allowed and you want to load new
software to a remote site via the DCC from a local shelf which already
contains the new software, log in (either locally or remotely) to the shelf
containing the new software, and then enter the
cpy-prog:tid or
cpy-prog:tid,pgmtype=nesw
command (where
tid
= the tid of the
shelf in which you want to install the software and the pgmtype is the type
of software you want to install). [The tid is the name given to a shelf
(network element) using the
set-ne:
command.] The
cpy-prog:
command will only copy software from a local controller to a remote
controller; it is not used to download software from a PC.
Summary of Contents for DDM-2000 OC-3
