ETC Element Classic, User Manual

Page: 147 / 687

System Basics 133
•
[About] & [Part] - displays the cue part number for each parameter.
•
[Expand] & [Effect] - opens the Effect Status Display (Tab 8).
Face Panel
•
[Shift] & [Escape] - to lock and unlock face panel.
•
Encoder Paging Keys & [Number] - pages to the desired encoder control page.
•
[Escape] & Encoder Paging Keys - locks the encoders. Press any encoder page button to
unlock.
•
[Flexi] & Encoder Paging Key - to invoke flexi encoder states.
•
[Fader Controls] & [Bump Button] - select a fader page on wings.
•
[Fader Page] & Rate Wheel - rolls the selected fader page. (Ti/Eos/Gio)
•
[Fader Page] & [number] - select a fader page on integral faders. (Ti/Eos/Gio)
•
[Fader Page] - increments the fader page by 1.(Ti/Eos/Gio)
•
[Shift] & [Fader Page] - decrements the fader page by 1. (Ti/Eos/Gio)
•
[Learn] & [Load] - opens the selected fader's configuration tools.
•
[Off] & [Load] - releases control of content, restoring to background and leave cue list
with pending cue in tact.
•
[Release] & [Load] - releases control of content, restoring to background, and resets cue
list to top.
•
[Shift] & [Go] or [Shift] & [Back] - cuts the pending cue or the previous cue.
•
[Shift] & [Load] - to remove content from a fader.
•
[Shift] & [Stage] - toggles Scroll Lock on and off.
Operations
•
[At] [Enter] - removes move information from selected channel/parameters.
•
[At] [At] - set to Level (as defined in Setup).
•
[Color] (Encoder Paging Key) & Encoder Movement - hold Color Point while adjusting
parameters.
•
[Copy To] [Copy to] - posts Move To on the command line.
•
[Full] [Full] - sets selected channels intensity to “full” and self terminates.
•
[Label] [Label] - appended to a record target command, clears the current label, this
includes show file labels.
•
[Recall From] [Recall From] - posts Recall From Cue to the command line.
•
[Record] [Record] - posts Record Only to the command line.
•
[Select Active] [Select Active] - Select Active minus submaster contributions.
•
[Shift] & [Select Active] - posts Select Non-Sub Active.
•
[Shift] & [Enter] - repeats last command line, unterminated; does a loop of last five
commands.
•
[Shift] & [At] - recalls last channel(s) and parameters without terminating; does a loop of
last five commands.
•
[Shift] & [Enter] - reselects the last command and leaves it unterminated; does a loop of
last five commands.
•
[Shift] & [Block] - posts Intensity Block to the command line.
•
[Shift] & [Clear] - clears the command line.
•
[Shift] & [Delay] - posts follow.
•
[Shift] & Encoder Paging Key - posts the category to the command line. For beam
subcategories, press Image, Form or Shutter twice to post Beam. (Ion/Gio)
•
[Shift] & Encoder Movement - accesses fine mode.
•
[Shift] & Encoder Push/ Toggle - posts the parameter to the command line. (Ion)
•
[Shift] & Gel Tile - cycles through three modes of Brightness.
•
[Shift] & [Full] or [Shift] & [Out] - flash on or flash out.
•
[Shift] & [+] or [Shift] & [-] - +% or -%.