Cisco WS-C3550-12G User Manual Download Page 386 | Manualshive

Page: 386 / 436

background image

11-34

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

IS-IS Management Window

Edit Network Table

The Edit Network Table area allows you to modify the Network Table. The following parameters must
be specified.

•

AFI

•

Area Address

•

System ID

•

Add Net—Adds a NET address to the IS-IS routing process.

•

Remove Net—Removes a NET address from the IS-IS routing process.

Network

The Network area provides the Network Table which describes the Network Entity Titles for an IS-IS
routing process. The NETs define the area addresses for the IS-IS area and the system ID of the router.
There must be at least one entry in this table in order for the IS-IS routing process to be functional. This
table displays the following columns:

•

AFI—Authority and Format Identifier (AFI). This is the first byte in the IS-IS NSAP Area Identifier.

•

Area Address—Area Address of the NET. Identifies the IS-IS routing area that the routing process
participates in.

•

System-ID—System ID of the NET. Unique identifier of the device in the routing area.

•

N-Selector—n-selector portion of the NET. Occupies the last byte of NET. Value is always 00.

Troubleshooting

The Troubleshooting area describes the IS-IS area configurations:

•

Command—Indicates the selected troubleshooting command. Possible values are:

–

Display IS-IS Database Detail

–

Display IS-IS Database Level 1

–

Display IS-IS Database Level 2

–

Display IS-IS Database I1

–

Display IS-IS Database I2

–

Display IS-IS spf-log

•

Command Table—Presents data according to the Command list selection.

Interfaces Tab

The Interfaces tab of the IS-IS Management window consists of a single area, Interface List. This area
lists the interfaces supported by a given IS-IS routing process. This table will be empty if CLNS routing
is not enabled on the managed device. The table contains one column:

•

Description—Identifies the supported interface. The interface may be an Ethernet, FastEthernet, or
GigabitEthernet. The interface may also be an Ethernet portchannel group or virtual LAN.

«
...
384
385
386
387
388
...
»

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WS-C3550-12G

Brand: Ubiquiti Pages: 32

Brand: Astronics Pages: 56

Brand: Cambium Networks Pages: 17

Brand: Sierra Wireless Pages: 62

AirPrime AR7558

Brand: Sierra Wireless Pages: 60

Brand: Sierra Wireless Pages: 69

Brand: Delta Pages: 5

Brand: 3Com Pages: 4

Brand: Globalsat Pages: 10

Brand: Sapido Pages: 102

Brand: Smart Mimic Pages: 2

Brand: Planet Networking & Communication Pages: 2

Brand: Planet Networking & Communication Pages: 2

Brand: Planet Networking & Communication Pages: 2

Brand: 3Com Pages: 8

Brand: Zte Pages: 279

Brand: Zte Pages: 17

Brand: InCoax Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands