manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 148

 

8-2

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

Interface Summary Management Window

Interface Summary Management Window

The Interface Summary Management window provides summary information for the interfaces. This 
window can be launched from a Chassis object or any Interface object within the Physical view.

To launch the Interface Summary Management window, perform one of the following:

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose CSM/7600 Manager > Physical > Interface > Summary Dialog.

•

Right–click a Chassis object within the Network or Physical containment views, then choose 
Physical > Interface > Summary Dialog.

The following figure is an example of the Interface Summary Management window.

Figure 8-1

Interface Summary Management Window

You can select multiple chassis and interfaces at a time from the object list on the left side of the window.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands