manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 171

 

8-25

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

Ethernet Interface Management Window

Figure 8-7

Ethernet Interface Management—Configure HSRP Group Window

The following fields are displayed in the Ethernet Interface Management - Configure HSRP Group 
window:

–

Group Number—Indicates the HSRP group number configured.

–

Virtual IP—Indicates the virtual IP address for the HSRP group.

–

Add—Adds an explicit HSRP group configuration to the interface.

–

Remove—Removes an explicit HSRP group configuration to the interface.

Secondary IP 

The Secondary IP area provides the following information:

•

HSRP Secondary Address Table—Describes secondary IP addresses of HSRP groups deployed on 
the interface. Data is displayed in the following columns:

–

Group Number—Unique identifier along of an HSRP group.

–

Secondary IP—Secondary IP address of HSRP group.

•

Modify—Launches the Ethernet Interface Management - Modify HSRP Group window that is 
displayed when the Modify button is pressed. Using the subdialog, the HSRP group configured on 
the interface maybe modified.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands