manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 270

 

9-6

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 9      Software Management

Software Management Window

IOS Config File Tab

The following areas are available on the IOS Config File tab of the Software Management window:

•

Startup Configuration

•

Running Configuration 

•

Backup/Restore Configuration

Startup Configuration 

The Startup Configuration area provides the following information:

•

Current Location—The location of the startup configuration file that will be used on the next restart. 
If this location is not set, then undefined is displayed. This attribute is read-only.

•

Startup Location—The location of the startup configuration file that was used the last time the 
system was booted up. This attribute is read-only.

•

View Startup Configuration—Displays the startup configuration in an Action Report.

Running Configuration 

The Running Configuration area provides the following information:

•

Last Changed—The time since the running configuration was last changed. This attribute is 
read-only.

•

Last Saved—The time since the running configuration was last saved. This attribute is read-only.

•

Auto Backup Enabled—The backup action is executed automatically whenever the Save Running 
Configuration action is executed.

•

View Running Configuration button—Displays the current running configuration in an Action 
Report.

•

Save Config to NVRAM—Saves the current running configuration to the location specified by the 
Startup Location attribute. Launches a confirmation dialog box.

Backup/Restore Configuration 

The Backup/Restore Configuration area provides the following information:

•

TFTP Host—The IP address or hostname of the TFTP server that the startup or running 
configurations were backed up to or restored from.

Note

The TFTP Host field must be configured in order to back up and restore the configuration. The 
TFTP Host must be accessible from the managed device, and there must be sufficient disk space 
on the host to store the device’s startup configuration.

•

Backup Status—Status of the last backup action. This attribute (read-only) has the following values:

–

Ok—The backup completed successfully.

–

Failed—The backup failed.

–

Not executed—The backup operation was not executed.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands