manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 254

 

8-108

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

POS Subinterface Management—Configuration Window

The following tabs are available on the POS Sub-interface Management—Configuration window:

•

Status Tab

•

Configuration Tab

•

POS Tab

•

Performance Tab

•

POS Statistics Tab

•

Routing Protocol Tab

•

Additional Notes Tab

Status Tab

The Status tab of the POS Sub-interface Management—Configuration window consists of a single area, 
Interface Status. The Interface Status area provides the following information to describe the general 
characteristics of the interface.

•

Description—Comment or a description to help you remember what is attached to this interface. The 
description is only put in the configuration to help you remember what specific interfaces are used 
for.

•

Index—String index of the interface. This attribute is read-only. 

•

Type—Indicates the type of interface distinguished by the physical and link layer protocols on the 
interface.

•

Operational Status—The current operational state of the interface. This attribute is read-only. This 
attribute has one of the following values: 

–

unknown

–

down

–

up

–

dormant—Interface is waiting for external actions (such as a serial line waiting for an incoming 
connection)

–

notPresent—Interface has missing (typically, hardware) components.

–

lowerLayerDown—Indicates that the primary channelized SONET interface has failed.

•

Administrative Status—The desired state of the interface. This attribute has one of the following 
values:

–

up

–

down

•

Number of Resets—Number of times the interface internally reset. This attribute is read-only.

•

Connector Present—Displays if a cable is attached to the parent interface (the OSM Channelized 
SONET Interface). These are the values:

–

yes

–

no

–

unknown—This value is used when the Administrative Status is not set to “up”. In this case, it 
cannot be determined if a connection is present or not.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands