Cisco WS-C3550-12G User Manual Download Page 364 | Manualshive

Page: 364 / 436

background image

11-12

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

OSPF Management Window

•

Add Redistribute—Enables route redistribution from another IP routing process into the OSPF
routing domain. Routes may be learned from an IS-IS, EIGRP, or BGP routing process.

•

Del Redistribute—Disables route redistribution from another IP routing process into the BGP
routing domain.

Distribution List Tab

The Distribution tab of the OSPF Dialog consists of a single area, Distribution List Table. In addition to
this area, the following subareas is available: Edit Distribution List Table.

The Distribution List Table area describes filtering of routing updates sent or received by the routing
process.

•

ACL ID—Unique identifier of an ACL for filtering routing updates sent or received by a routing
process. The ACL specifies which network routes will be permitted or denied in routing updates.
This field has the following values:

–

<1-199>—IP standard access list number.

–

<1300-2699>—IP expanded access list number.

–

alphanumeric—Named access list.

•

Direction—Indicates whether the filter will be applied against routing updates received by the
routing process or advertised by the routing process.

–

in—Applies to updates received.

–

out—Applies to updates advertised.

•

Interface—Identifies a particular interface that the filter is applied to. For an incoming filter,
suppresses routing updates received on a specific interface; if not specified, routing updates are
suppressed on all interfaces. For an outgoing filter, suppresses routes from being advertised on a
particular interface; if not specified, route advertisements are suppressed on all interfaces.

–

Null 0

–

FastEthernet <slot>/<port> (Native IOS only)

–

GigabitEthernet <slot>/<port> (Native IOS only)

–

GE-WAN <slot>/<port>

–

POS <slot>/<port>

–

ATM <slot>/<subslot>/<port>

–

Port-channel <n> (Native IOS only)

–

VLAN <n>

•

Protocol—Source routing protocol from which routes are being distributed into OSPF.

•

Source ID—Identifies a specific routing process instance that redistributed routes are derived from.

«
...
362
363
364
365
366
...
»

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WS-C3550-12G

Brand: Icom Pages: 2

Brand: Ubiquiti Pages: 36

Brand: OBERON Pages: 2

Brand: QWNET Pages: 23

Brand: Westfalia Pages: 10

RangeMax WNR3500

Brand: NETGEAR Pages: 2

Brand: M-Life Pages: 32

Brand: NETGEAR Pages: 2

Nfiniti Airstation WHR-G300N

Brand: Buffalo Tech Pages: 48

Brand: Billion Pages: 61

Brand: NETGEAR Pages: 2

Brand: TP-Link Pages: 94

MAX-STREAM MR6350

Brand: Linksys Pages: 28

Brand: Icidu Pages: 11

Brand: Icidu Pages: 16

Brand: Icidu Pages: 19

Brand: Trango Broadband Wireless Pages: 52

Brand: AmbiCom Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands