manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 38

 

1-8

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 1      Product Overview

Supported Software

Supported Software

The Cisco Catalyst Switch Manager 3.1 supports the following IOS and Catalyst OS software.

The following Native IOS releases are supported as listed by chassis family:

•

Catalyst 2950 series switch—12.1(11)EA1, 12.1(12c)EA1, 12.1(13)EA1, and 12.1(14)EA1

•

Catalyst 2970 series switch—12.1(14)EA1

•

Catalyst 3550 series switch—12.1(11)EA1, 12.1(12c)EA1, 12.1(12)EA1, 12.1(13)EA1, and 
12.1(14)EA1

•

Catalyst 4000 series switches:

–

Catalyst 4006 switch—12.1(12c)EW1 and 12.1(13)EW2

–

Catalyst 4503 switch—12.1(13)EW, 12.1(12c)EW1, and 12.1(13)EW2

–

Catalyst 4506 switch—12.1(12c)EW1 and 12.1(13)EW2

•

Catalyst 6500 series switch:

–

Catalyst 6509NEB switch—12.1(13)E, 12.1(13)E1, and 12.1(19)E1

–

Catalyst 6513 switch—12.1(13)E, 12.1(13)E4, and 12.1(19)E1

The following Pure Catalyst OS version is supported by the Catalyst 6506 and 6509 switch: 
7.2, 7.3, 7.4, 7.5 and 7.5(1), 7.6, and 8.2.

The following table identifies the Hybrid OS combinations supported by device.

Note

The above versions of CatOS and IOS have been extensively tested with the Cisco Catalyst Switch 
Manager software. Other versions and combinations of CatOS/IOS should interoperate with the 
manager, although there may be unanticipated incompatibilities or errors.

Table 1-2

Supported Hybrid OS Combinations

Device

IOS Version

Catalyst OS Version

Catalyst 6006 switch

12.1(12c)

6.3(10)

12.1(12c)E4

6.3(8)

12.1(12c)E4

6.3(9)

12.1(12c)E4

7.5(1)

12.1(12c)E4

7.6(1)

Catalyst 6509 switch

12.1(13)E

7.5(1)

12.1(19)E1

7.6(latest)

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands