Cisco WS-C3550-12G User Manual Download Page 375

Page: 375 / 436

11-23

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

BGP Management Window

The following tabs are available on the BGP Management window:

•

Details Tab

•

Neighbor Tab

•

Redistribution Tab

•

Distribution List Tab

•

Additional Notes Tab

Details Tab

The following areas are available on the Details tab of the BGP Management window:

•

BGP Information

•

BGP Network Path Attribute Table

•

Troubleshooting Command

BGP Information

The BGP Information area provides the following information:

•

Local AS—Autonomous system number for the local BGP process. This attribute has a value of 0
if BGP is disabled on the switch or router.

•

Enable—Enables BGP on the switch or router. Launches the BGP Management—Enable window.

Figure 11-9 BGP Management—Enable Window

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands

Cisco WS-C3550-12G, User Manual

Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands