manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Looking for a manual to maximize your Cisco WS-C3550-12G's potential? Look no further! Download a comprehensive, user-friendly manual for free from our website. Unlock the full power of this product by following the step-by-step instructions and unleash your network's true potential with ease. Visit manualshive.com to grab your free manual now!

Share
Download
background image

 

8-86

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/E3 Interface Management Window

General 

The General area contains the following information:

•

Link Up/Down Trap—Enables or disables linkUp and linkDown trap generation for the interface.

•

Max. Input Queue Length—Input queue length in packets.

•

Max. Output Queue Length—Output queue length in packets.

•

Delay—Specifies the delay in tens of microseconds for an interface or network segment. 

Note

The Delay attribute is an informational parameter used only to communicate the current 
bandwidth to the higher-level protocols (such as IGRP and EIGRP); you cannot adjust the actual 
delay of an interface with this command.

•

Bandwidth—Overwrites default bandwidth in kilobits per second. 

Note

The Bandwidth attribute is an informational parameter used only to communicate the current 
bandwidth to the higher-level protocols (such as IGRP, EIGRP, and OSPF); you cannot adjust 
the actual bandwidth of an interface with this command.

Layer 2 

The Layer 2 area contains the following information:

•

MAC Address—Displays the MAC address of the interface.

•

MTU—The size of the largest packet which can be sent/received on the interface, specified in octets.

•

Advanced Features—Launches the ATM/E3 Advanced Configuration window.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WS-C3550-12G

Daikin EKRACPUR1PA Security Instructions preview
EKRACPUR1PA
Brand: Daikin Pages: 2
Allied Telesis AT-MWS600AP Quick Installation Manual preview
AT-MWS600AP
Brand: Allied Telesis Pages: 2
Anaren A43364 User Manual preview
A43364
Brand: Anaren Pages: 27
4IPNET HSG260 User Manual preview
HSG260
Brand: 4IPNET Pages: 194
3Com 3CRWDR101A-75-US - OfficeConnect ADSL Wireless 54 Mbps 11g Firewall... User Manual preview
3CRWDR101A-75-US - OfficeConnect ADSL Wireless 54 Mbps 11g Firewall...
Brand: 3Com Pages: 146
TERABEAM AP-Ext-N User Manual preview
AP-Ext-N
Brand: TERABEAM Pages: 10
Aruba AP-270 Installation Manual preview
AP-270
Brand: Aruba Pages: 20
Konig CMP-WNAP10 Manual preview
CMP-WNAP10
Brand: Konig Pages: 41
Sparklan AP12275 M2 User Manual preview
AP12275 M2
Brand: Sparklan Pages: 9
SAF tehnika Integra-W Series User Manual preview
Integra-W Series
Brand: SAF tehnika Pages: 82
RocketFish RF-HTN104 User Manual preview
RF-HTN104
Brand: RocketFish Pages: 73
BAZOO 27213 User Manual preview
27213
Brand: BAZOO Pages: 2
T-Mobile Franklin T9 User Manual preview
Franklin T9
Brand: T-Mobile Pages: 4
T-Mobile Z915 Start Manual preview
Z915
Brand: T-Mobile Pages: 13
T-Mobile webConnect Jet Quick Start Manual preview
webConnect Jet
Brand: T-Mobile Pages: 15
LXE 6250 Configuration Manual preview
6250
Brand: LXE Pages: 6
Xiaomi Mi Router 3 Quick Installation preview
Mi Router 3
Brand: Xiaomi Pages: 3
Planex BLW-04EM User Manual preview
BLW-04EM
Brand: Planex Pages: 73

Brands by name

Popular brands

Load more brands