Cisco WS-C3550-12G User Manual Download Page 357

Page: 357 / 436

11-5

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 11 Routing Management

OSPF Management Window

Troubleshooting

The Troubleshooting area describes the OSPF area configurations:

•

Command—Indicates the selected troubleshooting command. Possible values are:

–

Border Routers

–

Virtual Link

–

OSPF <process-id>

–

OSPF <process-id> Database

–

OSPF <process-id><area-id> Database

–

OSPF <process-id><area-id> Database Router <link-state-id>

–

OSPF <process-id><area-id> Database Router Self Originator

–

OSPF <process-id><area-id> Database Router Adv Router <ip-address>

–

OSPF <process-id><area-id> Database Network <link-state-id>

–

OSPF <process-id><area-id> Database Summary <link-state-id>

–

OSPF <process-id><area-id> Database Asbr Summary <link-state-id>

–

OSPF <process-id><area-id> Database External <link-state-id>

–

OSPF <process-id><area-id> Database Summary

–

OSPF Interface <interfaceName>

–

OSPF Neighbor <interfaceName> Default

–

OSPF Request List <neighborId>

–

OSPF Request List <neighborId> <interfaceName>

–

OSPF Retransmission List <neighborId> <interfaceName>

•

Command Table—Presents data according to the Command list selection.

•

Interface names—Displays the applicable interface names according to the option selected from the
Command list.

The following fields may be edited as necessary depending on the selected troubleshooting
command:

–

Neighbor ID

–

Adv Router IP Address

–

Link State ID

The following field is read–only:

–

Interface Name

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands

Cisco WS-C3550-12G, User Manual

Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands