manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 284

 

9-20

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 9      Software Management

ACL Management Window

ACL Management Window

The ACL Management window describes a numbered or named access control list (ACL) on a 
Catalyst switch. The EM Controller supports standard and extended, named or numbered ACLs.

To launch the ACL Management window, perform one of the following:

•

Right–click a Site object within the Network or Physical containment views, then choose 
CSM/7600 Manager > Logical > Software > ACL.

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose Logical > Software > ACL.

•

Right–click a Software object within the Physical containment view, then choose ACL.

•

Right–click an ACL object within the Physical containment view, then choose ACL.

The following figure is an example of the ACL Management window.

Figure 9-5

ACL Management Window

The following tabs are available on the ACL Management window:

•

Details Tab

•

Additional Notes Tab

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands