manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 210

 

8-64

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/SONET Interface Management Window

Note

The logged data is available to you through the Cisco EMF Performance Manager. Refer to the 
Cisco Element Management Framework User Guide for more information about the Performance 
Manager.

Configuration Tab

The following areas are available on the Configuration tab of the ATM/SONET Interface Management 
window:

•

General 

•

Layer 2

•

Layer 3

•

Private VLAN Edge

•

Actions

General 

The General area contains the following information:

•

Link Up/Down Trap—Enables or disables linkUp and linkDown trap generation for the interface.

•

Max. Input Queue Length—Input queue length in packets.

•

Max. Output Queue Length—Output queue length in packets.

•

Delay—Specifies the delay in tens of microseconds for an interface or network segment. 

Note

The Delay attribute is an informational parameter used only to communicate the current 
bandwidth to the higher-level protocols (such as IGRP and EIGRP); you cannot adjust the actual 
delay of an interface with this command.

•

Bandwidth—Overwrites default bandwidth in kilobits per second. 

Note

The Bandwidth attribute is an informational parameter used only to communicate the current 
bandwidth to the higher-level protocols (such as IGRP, EIGRP, and OSPF); you cannot adjust 
the actual bandwidth of an interface with this command.

Layer 2 

The Layer 2 area contains the following information:

•

MAC Address—Displays the MAC address of the interface.

•

MTU—The size of the largest packet which can be sent or received on the interface, specified in 
octets. 

•

Advanced Features—Launches the ATM/SONET Advanced Configuration window.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands