manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 211

 

8-65

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/SONET Interface Management Window

Figure 8-19 ATM/SONET Advanced Configuration Window

You can select one chassis, more than one module, more than one port adapter, and more than one 
interface at a time from the object list on the left side of the window.

The ATM/SONET Advanced Configuration window contains one area named General.

General:

–

Local Proxy ARP—Indicates the status of local proxy ARP on the selected interface, enabled 
or disabled.

Layer 3 

The Layer 3 area contains the following information:

•

IP Address—Displays the IP address of the Layer 3 interface.

•

Netmask—Subnet mask of the interface IP address. Enabled bits indicate the network addressing 
bits in the IP address.

•

Clear IP Address button—After receiving confirmation, will remove the IP address setting for this 
interface.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands