manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 222

 

8-76

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/T3 Interface Management Window

Note

The Bandwidth attribute is an informational parameter used only to communicate the current 
bandwidth to the higher-level protocols (such as IGRP, EIGRP, and OSPF); you cannot adjust 
the actual bandwidth of an interface with this command.

Layer 2 

The Layer 2 area contains the following information:

•

MAC Address—Displays the MAC address of the interface.

•

MTU—The size of the largest packet which can be sent/received on the interface, specified in octets.

•

Advanced Features—Launches the ATM/T3 Advanced Configuration window.

Figure 8-21 ATM/T3 Advanced Configuration Window

You can select one chassis, more than one module, more than one port adapter, and more than one 
interface at a time from the object list on the left side of the window.

The ATM/T3 Advanced Configuration window contains one area named General.

General:

–

Local Proxy ARP—Indicates the status of local proxy ARP on the selected interface, enabled 
or disabled.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands