manualshive.com logo in svg

Cisco WS-C3550-12G, User Manual

Share
Download
Cisco WS-C3550-12G User Manual Download Page 229

 

8-83

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 8      Interface and Subinterface Management

ATM/E3 Interface Management Window

ATM/E3 Interface Management Window

The ATM/E3 Interface Management window describes a physical and logical enhanced ATM/E3 
interface of the PA-A3-E3 FlexWAN port adapter on the Catalyst switch. This window can be launched 
from the ATM port adapter or the ATM/T3 interface object within the Physical view.

To launch the ATM/E3 Interface Management window, perform one of the following:

•

Right–click a Network Element object within the Network or Physical containment views, then 
choose CSM/7600 Manager > Physical > Interface > ATM/E3.

•

Right–click a Chassis object within the Network or Physical containment views, then choose 
Physical > Interface > ATM/E3.

The following figure is an example of the ATM/E3 Interface Management window.

Figure 8-22 ATM/E3 Interface Management Window

You can select multiple ATM/E3 Interfaces, port adapters, FlexWAN modules, and chassis at a time from 
the object list on the left side of the window.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands