Cisco WS-C3550-12G User Manual Download Page 42

Page: 42 / 436

2-4

Cisco Catalyst Switch Manager User Guide

OL-4930-01

Chapter 2 Basic Concepts

Cisco Catalyst Switch Manager Objects and Interfaces

These Cisco Catalyst Switch Manager objects have the following hierarchical organization:

•

Chassis

–

Power supplies

–

Supervisor engine modules:

Ethernet interfaces

–

Ethernet modules:

Ethernet interfaces

–

Switch Fabric Modules

–

FlexWAN Modules

Port adapters:

ATM port adapters

ATM SONET interfaces

ATM E3 interfaces

ATM T3 interfaces

–

OSM GeWAN Modules

OSM GeWAN interfaces

–

OSM PoS Modules

Ethernet interfaces

OSM PoS interfaces

–

OSM Channelized SONET Modules

Ethernet interfaces

OSM ChSONET interfaces

OSM Serial Subinterfaces

OSM PoS Subinterfaces

–

Content Switching Modules

Logical Objects

The Cisco Catalyst Switch Manager models the following logical components:

•

Software—Represents the IOS image and configuration file on the Catalyst switch

•

EtherChannels—Creates, deletes, and modifies EtherChannels on the Catalyst switch

•

VLAN—Lists, creates, and deletes VLAN interfaces on the Catalyst switch

•

Loopback—Used to isolate the fault on an end-to-end circuit

•

Syslog—Represents the standard syslog messaging protocol on the Catalyst switch

•

ACL—Represent access control lists, both standard and extended, named and numbered

•

NDE—NetFlow Data Export (NDE) makes traffic statistics available for analysis by an external data
collector

•

QoS—Enables and manages the global quality of service (QoS) engine.

Summary of Contents for WS-C3550-12G





















































































































































































































































































































































































































































Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands

Cisco WS-C3550-12G, User Manual

Search results

Summary of Contents for WS-C3550-12G

Reviews:

Brands by name

Popular brands